- DREAMBOX FLASH WIZARD PRO INSTALL
- DREAMBOX FLASH WIZARD PRO SOFTWARE
- DREAMBOX FLASH WIZARD PRO DOWNLOAD
To finish setting up your UDM-Pro, please read UniFi - Set Up a Dream Machine Pro. Note: For more information about compatible fiber SFP modules, refer to our Help Center article.Ĭonfiguring and Connecting Devices to the UDM-Pro Insert your SFP Fiber Module (or compatible third-party equivalent) into Port 11. Remove the rubber plug from the SFP+ LAN port (Port 11 in the Hardware Overview table).
DREAMBOX FLASH WIZARD PRO DOWNLOAD
The advantage of this wired configuration is often stronger, steadier download and upload speeds.Ĭonnect one end of your fiber optic cable to the desired device. Note: A LAN, or Local Area Network, connection will directly connect, or "hard line," an individual device (e.g., laptop, game console, etc.) to your UDM-Pro via a separate Ethernet cable. Note: For more information about compatible fiber SFP modules, refer to ourĬonnecting Devices to the UDM-Pro via LAN Cable Insert your SFP Fiber Module (or compatible third-party equivalent) into Port 10.Ĭonnect the other end of your fiber optic cable to the SFP Fiber Module. Remove the rubber plug from the SFP+ Internet port (Port 10 in the Hardware Overview table). Ensure that your power source can accommodate this, as well as any other devices sharing the UDM-Pro's power supply.Ĭonnecting the UDM-Pro to Your Internet Modem or RouterĬonnect one end of your Ethernet cable to your modem or router, then connect the other end to the RJ45 Internet port on the front of the UDM-Pro (Port 9 in the Hardware Overview table).Ĭonnecting the UDM-Pro with a Fiber Internet AdapterĬonnect one end of your fiber optic cable to your modem or router. Note: The UDM-Pro's voltage output range is 100-240 volts. Insert the power cord into the back of the UDM-Pro.Ĭonnect the power cord to a standard AC outlet, surge-protected power strip, or a UPS device. IMPORTANT! We strongly recommend connecting the UDM-Pro to an Uninterruptible Power Supply (UPS), or battery backup device, to prevent power instability issues and hardware damage that may result from relying on the local AC power of a standard outlet. Thread the mounting screws (B) through the rack-mount brackets and the circular ends of the cage nuts. If your mounting rack's holes are rectangular:įasten two cage nuts (C) to each of the mounting rack's support legs. If your mounting rack's holes are circular, fasten two mounting screws (B) through the rack-mount bracket and the rack's support legs.
Position the first rack-mount bracket (F) so that its four holes align with the four threading holes on either side of the UDM-Pro.įasten the first rack-mount bracket using four bracket screws (A), then repeat the process with the second rack-mount bracket.Īlign the front-facing holes of the rack-mount brackets with those of the wide rack's support legs. Note: Although the cabling can be located outdoors, the UDM-Pro itself should be housed inside a protective enclosure. For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.Standard-sized, 19 " wide rack with a minimum of 1U height available.Rack Mounting the UDM-Pro Installation Requirements Reinsert the tray into HDD bay and close the front panel tab. Remove all screws attaching the HDD's chassis to the tray, then remove the device. Open your UDM-Pro's front panel and pull out the HDD mounting tray. After a few seconds, the LED will turn off, and the device will automatically reboot.Ĭonnect the included Power Cord to the Power port.Įnsure that your UDM-Pro is fully powered down and unplugged prior to removing your HDD. Press and hold the Reset button for about 10 seconds until the display indicates that the device has reset itself. The device should be running after bootup is complete. By default, it is set to DHCP Server with the fallback IP address, 192.168.1.1/24. The SFP+ port supports a 1/10G Ethernet connection. The RJ45 port supports a 10/100/1000 Ethernet connection. By default, they are set to DHCP Server with the fallback IP address, 192.168.1.1/24. The RJ45 ports support 10/100/1000 Ethernet connections.
DREAMBOX FLASH WIZARD PRO INSTALL
Install a 3.5" or 2.5" HDD (not included) to use the device as an NVR for UniFi Protect. SFP+ Speed/Link/Activity LED (Ports 10 - 11) RJ-45 Speed/Link/Activity LED (Ports 1 - 9)
DREAMBOX FLASH WIZARD PRO SOFTWARE
The software will also display the location of the device on the map. This indicates that you clicked Locate in the UniFi Network Application. A display message of "UDM-Pro is Starting."
0 kommentar(er)
